Engineering Blog — Page 2
Latest weekly MATLAB/Simulink, OEM, PhD research and engineering simulation articles. New posts appear first. Topics cover OEM model validation, PhD methodology, renewable energy systems, EV powertrain, antenna/RF simulation, control systems, power electronics and research documentation for AU / UK / CA / Global users.
Active and reactive power tracking for a three-phase PWM rectifier — Model Guide
Model architecture, control or physics setup, primary outputs, and a reproducible reading of the simulation.
Read technical guide →Neutral-point balancing and DC-link energy in 3-level NPC inverters — Validation
A research-oriented checklist for boundary conditions, modelling uncertainties, convergence and credible comparisons.
Read technical guide →How to verify THD and net-grid power in active load emulators — Research Comparison
How to compare baselines, stress-test assumptions and write a reproducible engineering results section.
Read technical guide →Adaptive MPPT and SEPIC conversion in solar battery charging — Model Guide
Model architecture, control or physics setup, primary outputs, and a reproducible reading of the simulation.
Read technical guide →Battery current limiting and CC/CV transitions in a Simulink charger — Validation
A research-oriented checklist for boundary conditions, modelling uncertainties, convergence and credible comparisons.
Read technical guide →SEPIC inductor ripple and energy-efficiency validation under irradiance steps — Research Comparison
How to compare baselines, stress-test assumptions and write a reproducible engineering results section.
Read technical guide →Net harvested energy versus MPPT tracking efficiency in solar boost converters — Model Guide
Model architecture, control or physics setup, primary outputs, and a reproducible reading of the simulation.
Read technical guide →Boost converter startup and low-irradiance challenges in Simscape — Validation
A research-oriented checklist for boundary conditions, modelling uncertainties, convergence and credible comparisons.
Read technical guide →Adaptive MPPT benchmarking for ultra-low-power PV energy harvesting — Research Comparison
How to compare baselines, stress-test assumptions and write a reproducible engineering results section.
Read technical guide →PEM Electrolyzer Simulation Research: Polarization Curves vs Hydrogen Yield
Polarization-curve fitting and hydrogen-production prediction answer different questions. The first characterizes cell-voltage losses with current; the second t
Read technical guide →Battery Pack Thermal Management vs Thermal Runaway: COMSOL Modelling Boundaries
Liquid-cooling performance during a routine 3C discharge and thermal runaway propagation are physically different analyses that should not share unexplained hea
Read technical guide →PMSM Sliding Mode Observer FOC: Position Estimation and Torque Ripple
Sensorless PMSM FOC combines two control problems: current/torque regulation and rotor-angle estimation. Their apparent performance must be assessed separately.
Read technical guide →Adaptive Solar MPPT: Comparing a SEPIC Battery Charger and Boost Energy Harvester
Adaptive MPPT can command different power converters, but the useful metric depends on whether the goal is safe battery charging or ultra-low-power energy captu
Read technical guide →HFSS Shared Aperture Antennas: SIW Phased Arrays, Dipoles and Beam Steering
A shared-aperture antenna places different radiator functions into the same physical area. Dual-band matching alone does not prove usable independent operation.
Read technical guide →Three-Phase Active Load Emulator: PWM Rectifier, NPC Inverter and Power Balance
An active load emulator commands apparent load behaviour at an input interface while a regenerative converter can return most absorbed power to the supply.
Read technical guide →LSTM-Based Adaptive MPPT for Grid-Connected Solar PV Systems Using MATLAB Simulink & Simscape — Simulation Model and Output Guide
Explore an LSTM-informed maximum power point tracking workflow for a grid-connected photovoltaic system where irradiance, temperature and inverter o.
Read technical guide →How to validate LSTM-based MPPT under irradiance transitions
Design separate irradiance ramps, abrupt shading changes and temperature steps. Report held-out prediction error, tracked PV power and DC-link respo.
Read technical guide →SEPIC-Derived Semi-Bridgeless PFC Converter for Battery Charging in MATLAB Simulink & Simscape — Simulation Model and Output Guide
Examine a SEPIC-derived semi-bridgeless power-factor-correction front end for battery charging, focusing on shaping the mains input current while re.
Read technical guide →